Skip to main content

Port labels, addresses and setup pages from vendor documentation · checked Nov 2026 · Methodology

How to set up a router

ResetWANLAN 1LAN 2LAN 3LAN 4PowerSSID ROUTER-4B21
Setup 192.168.0.1
Password printed below
Wi-Fi
The port the cable goes into is the one marked WAN. LAN ports are for wired devices, not for the modem.

By RouterPanel Editorial · Updated

Short answer

Connect the modem's Ethernet cable to the router's WAN or Internet port. Power the modem first, the router second, then open the setup address on the label and change both passwords.

Short answer. Connect the modem's Ethernet cable to the router's WAN or Internet port. Power the modem first, the router second, then open the setup address on the label and change both passwords.

Before you start

Put these out before you touch a port:

  • the router and its power adapter;
  • the modem or the fiber ONT, with the line live;
  • two Ethernet cables: one for the modem, one for the setup computer;
  • the label from the router's back or underside, or a photo of it;
  • the admin password, if the provider set one;
  • a paper clip for the reset pinhole;
  • the connection details from the provider, if the line needs a login.

The label prints the setup address, the factory network name and the factory password; copy them before it goes anywhere. If the terms are new, read what a router is and router versus modem first, and use the modem to router cable guide for the hardware.

Power and cabling

The order follows the Motorola MB8600 guide and the TP-Link FAQ, two of the sources that print a sequence.

  1. Power off both devices.
  2. Cable the modem. On a cable line the coax goes to the port ARRIS calls the Cable connector, not an RJ45 plug. On fiber the provider's PON cable stays in the ONT.
  3. Run the Ethernet across. One RJ45 cable from the modem's Ethernet port to the router's WAN or Internet port; the connection guide covers the device side.
  4. Power the modem and read its LEDs. Plug the modem in before the router and wait for the lights to settle before the next step.
  5. Power the router. No cable moves after this point.

On a Netgear the Internet light should come on solid; off means no modem link and amber a link without internet. The Cox page for the same modem skips the power-off sequence, so the powered order is a preference, not a gate.

The port the cable goes into

WAN and Internet are the same port on a consumer router. Netgear prints it as WAN / "Internet"; TP-Link's FAQ prints "Internet". The cable from the modem goes there.

Modems are looser. The ARRIS SB8200 has no WAN label at all: its two Ethernet ports are numbered 1 and 2. The Motorola MB8600 has four Ethernet ports labelled LAN 1 to 4; its FAQ says to connect port 1 to the router and not to use ports 3 and 4 for port bonding.

LAN ports face the home devices, apart from the Internet port on a TP-Link; the Calix 844G numbers its four Ethernet ports 1 to 4. Any of them takes a computer, a switch or a second access point.

Port, cable and the step that uses it
PortCableStep that uses it
WAN / "Internet" on the routerRJ45 Ethernet from the modem3
LAN 1–4 or numbered LAN ports on the routerRJ45 to a computer, switch or access pointlater
"Cable" connector on the modemCoaxial cable from the wall outlet2
ETHERNET (LAN) on the Motorola modemRJ45 across to the router3
Ethernet LAN on the Verizon ONTRJ45 across to the router3
Power jackBarrel plug from the router's adapter5
Reset pinholePaper clip, held in for a resetlater

The Verizon ONT takes the provider's fiber patch cable on an SC/APC fitting and RJ45 on the side that faces the router; the fiber connector itself stays put.

Place the router

Put the router where the signal has the least to cross: central, off the floor on a shelf or table, out of a cupboard, with a clear line of sight. Keep it away from metal objects and solid surfaces, and from microwave ovens and cordless phones. Stand the antennas upright.

If one room stays weak, read how to improve a Wi-Fi signal before buying anything.

Open the setup page

Connect the computer with the second Ethernet cable, or join the factory network on the label. Open a browser and type the label's setup address; some print a word address such as routerlogin.net instead of a number. The router login guide covers a rejected factory password.

Log in with the printed admin name and password, then change the admin password and keep it away from the router.

The first screen asks how the line gets its address: automatic, a login, or a fixed address. Pick what the provider sent you. On most cable lines the address is automatic; a login needs the provider's user name and password, and the wrong choice leaves the router offline.

Name the network and set the password

The network name and the Wi-Fi password are the radio settings. Replace both factory values before a device joins. A name that says where the router is beats the model name, which tells a stranger the maker and the default credentials.

Give it a password long enough that it cannot be guessed and pick the strongest encryption listed; the password guide shows the field. Save; any device on the old Wi-Fi drops and reconnects.

The secure section below closes the remaining switches.

Secure the router

The admin password is already yours. These switches matter:

  • Turn off administration from the internet side. The setting is called remote management, and it is off by default.
  • Leave the firewall on; it is on by default and TP-Link recommends keeping the default.
  • Turn off WPS unless you pair devices with it; the WPS button pairs a device with a press.

A VPN on the router protects every device behind it; the VPN guide covers the client setup.

Update the firmware

Log in, find the firmware or update entry, and run it over the Ethernet cable; do not cut the power while the update writes. The firmware guide has the menu paths.

Add a guest network

A guest network gives visitors their own name and password and keeps them off the main network's devices. Turn it on in the same admin page and leave isolation on; the guest Wi-Fi guide follows the same steps.

Test the connection

Test from the wired computer first, then unplug the cable and test the Wi-Fi. If the wired test fails, check the ports before anything else: the modem's Ethernet must be in the router's WAN or Internet port, never a LAN port. The router not connecting guide takes the failure from there.

Add a second router later

A second router joins through a LAN port on the first one, never its WAN port, and runs in access point mode with its own DHCP off. On the Calix 844G that is one of Ethernet ports 1 to 4.

A mesh network replaces the router and roams one name; a Wi-Fi extender adds to it, and some create a second network name. The router table compares the hardware.

Questions

Do I just plug in a new router?

Plug the modem's Ethernet into the WAN or Internet port, power the modem first, then the router, and change both passwords before devices join.

Can you set up a router by yourself?

Yes. It happens on the label and in the router's own setup page; if the home is already wired and the provider offers a self-install kit, you may get online without a technician visit.

Do I need to call my internet provider first?

You need to know the line's connection type; if you are unsure, contact your ISP directly.

Sources

  1. kb.netgear.com: What do the LEDs on my NETGEAR router mean · checked Nov 19, 2026
  2. netgear.com: connecting cable modem and router · checked Nov 19, 2026
  3. arris.my.salesforce-sites.com: SB8200 Ethernet Ports · checked Nov 19, 2026
  4. arris.my.salesforce-sites.com: SB8200 First Time Installation · checked Nov 19, 2026
  5. tp-link.com: 3841 · checked Nov 19, 2026
  6. tp-link.com: 2982 · checked Nov 19, 2026
  7. help.motorolanetwork.com: mb8600 product guides · checked Nov 19, 2026
  8. en-us.support.motorola.com: 177990 · checked Nov 19, 2026
  9. cox.com: arris sb8200 · checked Nov 19, 2026
  10. verizon.com: knowledge base 312255 · checked Nov 19, 2026
  11. searanchconnect.org: Calix_844G_UG · checked Nov 19, 2026
  12. kb.netgear.com: How do I log in to my NETGEAR router · checked Nov 19, 2026
  13. kb.netgear.com: How do I perform a factory reset on my NETGEAR router · checked Nov 19, 2026
  14. tp-link.com: 87 · checked Nov 19, 2026
  15. tp-link.com: 776 · checked Nov 19, 2026
  16. tp-link.com: 497 · checked Nov 19, 2026
  17. tp-link.com: 1384 · checked Nov 19, 2026
  18. tp-link.com: 2796 · checked Nov 19, 2026
  19. tp-link.com: chapter 1 get to know about your router · checked Nov 19, 2026
  20. support.linksys.com: 81 en · checked Nov 19, 2026
  21. asus.com: 1011232 · checked Nov 19, 2026
  22. dlink.com: how do i upgrade the firmware on my router · checked Nov 19, 2026
  23. eero.com: how do i share my eero network with guests · checked Nov 19, 2026
  24. verizon.com: verizon router guide · checked Nov 19, 2026

RouterPanel. "How to set up a router." Updated Nov 19, 2026. https://howtosetuparouter.com/