Read the default gateway from your own device: ipconfig on Windows, the TCP/IP pane on macOS, or the Wi-Fi network details on a phone. That address is the router's private IP, and it opens the login page. NETGEAR routers use 192.168.1.1 or 192.168.0.1 by default.
Why the address is a default gateway
The default gateway is the exit from your home network. Every device keeps a small routing table, and the gateway entry is the one it uses when the destination lies outside the local subnet. The router supplies that entry over DHCP, so the value in it is the router's own LAN address.
The same number serves the admin page. Type it into the browser's address bar, and the router answers with a login screen. The admin password is the one you chose at setup; only a factory reset restores the printed default. The login step is set out in log in to your router, and the password change that follows in change your Wi-Fi password.
The cable from the modem belongs in the WAN port; the gateway you are hunting sits on the LAN side, where a laptop or phone meets the router.
The address is not the router's public IP. The public one is handed out by the ISP and faces the street; the gateway is private, faces the rooms, and it is the one that opens the admin page from inside.
Neither the maker nor the range is free. RFC 1918 reserves three blocks for private networks, and IANA has labelled all three Private-Use since the allocation in February 1996. Home gateways sit inside that space. Within it, makers print a default, and the address can be changed.
| Block or maker | Address | Scope |
|---|---|---|
| Private ranges reserved by the standard | ||
| RFC 1918, 10/8 | 10.0.0.0 - 10.255.255.255 | Labelled Private-Use |
| RFC 1918, 172.16/12 | 172.16.0.0 - 172.31.255.255 | Labelled Private-Use |
| RFC 1918, 192.168/16 | 192.168.0.0 - 192.168.255.255 | Labelled Private-Use |
| Default addresses printed by makers | ||
| NETGEAR | 192.168.1.1 or 192.168.0.1, and routerlogin.net | Per model; changeable |
| TP-Link | 192.168.0.1, and tplinkwifi.net | Model dependent; changeable |
| Linksys | 192.168.1.1, and myrouter.local | Changeable |
| D-Link DIR series | 192.168.0.1, and dlinkrouter.local | Changeable |
| Verizon Router CR1000A | 192.168.1.1, and mynetworksettings.com | Certificate warning; Proceed |
| Verizon Internet Gateway | 192.168.1.1 on WNC-CR200A and ARC-XCI55AX; 192.168.0.1 on ASK-NCQ1338 and ASK-NCQ1338FA | Differs by model |
A printed default only applies until someone changes it. The gateway field on the device is the reliable figure, and the steps below read it.
Windows
Wi-Fi or an Ethernet cable has to carry the PC to the router before the command can return anything. Join the network first, then read the adapter that is up.
- Press Start, type cmd, and open Command Prompt.
- Type ipconfig and press Enter.
- Find the adapter in use, Wi-Fi or Ethernet, and read its Default Gateway line.
- Take the IPv4 address on that line, not the IPv6 one.
The adapter is named Wi-Fi or Ethernet. Read the one that carries traffic; a VPN adapter may list a different number, so ignore it unless it is the one you need.
Windows 11 also shows the figure without a command: Settings > Network & internet > View Hardware and Connection Properties, then the Default Gateway line, taking the IPv4 value.
macOS
Wi-Fi has to be joined, because the address lives under the Wi-Fi service and not under Ethernet.
- Open System Settings and choose Network.
- Select Wi-Fi, then Details.
- Open TCP/IP and read the Router field.
Ventura and later use this path. Monterey and earlier keep the same field under System Preferences > Network > Advanced > TCP/IP.
The terminal answers in one line: netstat -nr | grep default. The first address after the word default is the gateway.
iPhone and iPad
Wi-Fi has to be joined before the field appears. Open Settings > Wi-Fi, then tap the i beside the connected network.
- Read the address listed as Router.
- Take the IPv4 value.
The field comes from the network's IP configuration. In a manual (Static) configuration the Router field stays and is filled by hand, so it holds what was typed; only under Automatic does it hold the router's own address.
No app is needed for the lookup: the field is part of the Wi-Fi settings.
Android
Wi-Fi has to be the connected network. The path differs by build, so start from the Wi-Fi list rather than from a remembered menu.
- Pixel: Settings > Network & internet > Internet. Samsung: Settings > Connections > Wi-Fi.
- Tap the gear beside the joined network.
- Scroll to Network Details.
- Read Gateway.
Some builds print Gateway on the network's details screen without an Advanced step.
Linux
An Ethernet cable or a Wi-Fi link has to be up before a route exists.
The direct command is ip route show default. A working line reads default via 192.168.1.1 dev wlan0, and the address after via is the gateway. The full table from ip -4 route gives the same entry.
NetworkManager prints it as IP4.GATEWAY: nmcli device show wlan0 | grep IP4.GATEWAY. On older systems, route -n marks the row with a UG flag, and netstat -rn works the same way.
Check the address is a private one
RFC 1918 sets aside three blocks for private networks:
- 10.0.0.0 to 10.255.255.255
- 172.16.0.0 to 172.31.255.255
- 192.168.0.0 to 192.168.255.255
IANA labels each one Private-Use with no global reachability. Test the first octets: a 10 address, a 172 address with a second octet from 16 to 31, or any 192.168 address is private.
Outside them, 100.64.0.0/10 (Shared Address Space), 127.0.0.0/8 (Loopback) and 169.254.0.0/16 (Link Local) are also non-public, so a gateway can sit outside RFC 1918 and still not be a public address.
When no gateway appears
An empty Router or Default Gateway field means the device has no gateway to show. Work through these before touching anything red.
- Replug the Ethernet cable, or rejoin the Wi-Fi network by hand.
- Set the adapter's IPv4 method back to Automatic, or DHCP.
- Read the label on the back, bottom or side of the router, where the default address is printed.
- Power-cycle the router and the modem, then wait for the LEDs to settle; the steps are in why your router is not connecting.
- Press the reset pinhole with a paper clip, hold for seven seconds, and release.
A reset returns the settings to the factory defaults, including the default admin login, so do this last. Some Verizon units answer the default address with a certificate warning; choose Advanced, then Proceed.
If the adapter was given a manual address earlier, the gateway may be a number typed there. Switch the method back to Automatic and reconnect.
A field that fills but a page that will not load is a different fault, and connect to a router covers it.
Questions
What is the 192.168 1.1 router IP address?
It is a private address in the 192.168/16 block, and NETGEAR and Linksys print it as a default. TP-Link and D-Link ship with 192.168.0.1 instead. Type the number into a browser's address bar to reach the login page.
How can I check the IP address of my WiFi router?
Read the default gateway on a connected device: ipconfig on Windows, the Router field under TCP/IP on macOS, or the Gateway field under DHCP on iPhone and Android. The same number is usually on the label.
How to find router IP address without connecting?
Read the label on the back, bottom or side of the router, or open the maker's support page. The number is printed there because the router needs one before any device joins. A maker's support page lists the same default per model. Reaching the admin page still needs a connection, wired or wireless.