Cable the line into the modem, then the modem into the router's WAN port. The modem takes the line and the router shares it, and the router's LAN ports face your devices.
Two different jobs
A modem and a router sit at opposite ends of one short cable because they answer different questions. The modem receives the provider's signal and converts it into a format your devices can use; the router takes that connection and distributes it to your devices. TP-Link puts it as a translator and as a hallway that directs traffic to every room, and a house that needs both jobs has one of each.
What the modem does
The modem terminates the provider's line. On coax, DOCSIS 3.0 was built to bond downstream QAM channels: the original equipment supported 4, each 6 MHz wide in North America, and the next generation supported 8, then 16, then 24 and finally 32, as CableLabs described on 22 June 2023, which is how a cable modem turns a television plant into data. DOCSIS 3.1 raises that ceiling, and as of 18 November 2026 CableLabs claimed downstream data speeds of 10 Gbps and upstream speeds of up to 1 Gbps, as network capability rather than a promise for one modem. On fibre that equivalent box is the fiber modem, often called an optical network terminal (ONT), and the GPON recommendation G.984.2 (08/2019) set nominal line rates of 1 244.160 and 2 488.320 Mbit/s downstream, plus 155.520, 622.080, 1 244.160 and 2 488.320 Mbit/s upstream, before protocol overhead. Whichever line it serves, the modem hands one Ethernet connection to the router.
What the router does
The router takes the one connection the modem offers and divides it. Its WAN port is the only port that faces the line; the LAN ports face your own devices. The router runs DHCP so each device gets an address without a hand-typed configuration, and it hands those addresses out from the private blocks RFC 1918 reserved in February 1996: 10.0.0.0 to 10.255.255.255, 172.16.0.0 to 172.31.255.255, and 192.168.0.0 to 192.168.255.255. It keeps a routing table to move packets between the LAN ports and the WAN, and teal work sits here too, because this is the box that names the SSID, sets the band and picks the channel. Red belongs here as well: a factory reset, through the reset pinhole on models that have one, returns all of it to the factory state.
Why most homes need both
One modem port feeds one Ethernet device. A router is what lets a laptop, two phones and a television share that single port at the same time, each on its own LAN address; a modem alone gives one wired device and nothing else, and a router alone has no line to share. Keeping the jobs in two boxes also means you can upgrade one component without replacing both, and a Wi-Fi problem is often the router's, not the modem's.
When one box does both
A gateway hides both jobs in one housing: a line port, a few LAN ports and a radio, sold by the provider as a single unit, which TP-Link calls "a single device that handles both functions." The Verizon Router CR1000A and CR1000B are that shape, with "Ethernet WAN" for the ONT or a 5G Modem, three Ethernet LAN ports, and an F-type coax port for MoCA devices, which Fios TV needs too. One box means fewer devices on the shelf, but the provider pushes its firmware automatically and there is no second box to swap. The two jobs do not change inside it; only the housing does, and the setup walkthrough covers the rest of the configuration.
Which cable goes where
Read the label before choosing the hole; the stickers and socket colours in the diagrams are examples, not a vendor print. Every device below marks its line side, and the standards rows show what that line physically is. A label of WAN or Ethernet WAN is the one the modem cable takes; a LAN label is the one your own devices take.
| Device or interface | Line-side label | Line and connector | LAN side | Scope and date |
|---|---|---|---|---|
| TP-Link Archer AX10 and AX1500, router | "WAN Port" | Ethernet to a DSL or cable modem, or to an Ethernet jack; RJ45 | LAN ports | Archer AX10 / AX1500 v1, 18 November 2026; other models differ |
| Verizon Router CR1000A and CR1000B, gateway | "Ethernet WAN" | Ethernet to the ONT or a 5G Modem; RJ45 | three Ethernet LAN ports, F-type coax for MoCA devices (Fios TV needs it) | CR1000A / CR1000B, 18 November 2026 |
| GPON fibre line, ITU-T G.984.2 | no panel label | fibre; 1 244.160 and 2 488.320 Mbit/s down, 155.520, 622.080, 1 244.160 and 2 488.320 Mbit/s up | LAN ports on the ONT | G.984.2 (08/2019), nominal rates before protocol overhead |
| DOCSIS 3.1 coax line, CableLabs | no panel label | coax, F-type; 10 Gbps down, up to 1 Gbps up | LAN ports on the modem | page of 18 November 2026; network capability, not one modem |
| DOCSIS 3.0 bonding, CableLabs | no panel label | coax; original equipment 4 bonded downstream QAM channels (6 MHz wide in North America), later 8, 16, 24, 32 | LAN ports on the modem | blog of 22 June 2023; channel counts, no bit rate |
| RFC 1918 private addressing | LAN port labels | not a line; 10.0.0.0 to 10.255.255.255, 172.16.0.0 to 172.31.255.255, 192.168.0.0 to 192.168.255.255 | all LAN ports | RFC 1918, February 1996 |
Two limits travel with the table. The TP-Link labels describe one model family, and other models arrange the ports differently. The DOCSIS and GPON rates are line capability before any overhead, not what one subscriber sees.
Extending the network without a second router
A second router behind the first adds a second NAT layer and a second network name. An extender dodges that: it rebroadcasts the existing signal, though some create a second network name, and EasyMesh models join the existing network under one name. Teal, so the work is a radio setting and not a cable, and the extender is configured in its own page or paired with WPS. Throughput roughly halves on the repeated link because the extender talks to the router on the same channel it serves clients on. Place it about halfway between the router and the dead zone, in sight of both. A mesh system replaces the router instead: the main unit acts as the router and the nodes relay under one name with automatic handoff, and it costs more. So an extender adds to the first router while a mesh system takes its place. If the gap can take a cable, a wired Ethernet backhaul is the blog's other option. The mesh network setup and the modem to router connection pages take the next step.
Questions
Can you use a router without a modem?
Only if something upstream supplies the line. A router's WAN port expects an Ethernet handoff from a modem, an ONT or a wall jack that already carries internet; with none of those it routes between your devices and reaches nothing.
What is the difference between a router and a modem?
The modem ends the provider's line and hands over one Ethernet connection. The router takes that connection and shares it across your devices on private LAN addresses, and the radio that serves Wi-Fi lives in the router. The router definition covers the parts in full.