Move the router to a central shelf, off the floor and clear of walls, then set the 2.4 GHz channel to 1, 6 or 11. Do the free fixes before buying an extender.
Start with placement
The back panel limits where the box can go: the WAN port needs the modem cable and the power jack needs a socket, so choose a spot that serves both without a long run under a rug.
- Put it in the open centre of the home. Linksys asks for a central area away from walls and corners; the FCC's home-network tips ask for a central location.
- Raise it. eero says halfway between floor and ceiling. TP-Link gives roughly 1 to 1.5 ft, and a TP-Link blog written for Philippine concrete-hollow-block homes asks for at least one metre.
- Leave at least 20 to 30 cm clear on every side. TP-Link gives that clearance for a router sitting on a TV console or shelf.
- Keep 1 to 2 m from a microwave, television, Bluetooth speaker, cordless phone or baby monitor, and at least 1 m from a fish tank or water dispenser.
- Never stand it on the floor. Linksys says the floor and the ground absorb the signal.
- Do not put it behind a cabinet door or in a corner. NETGEAR says no corner and no wall contact.
The makers disagree on height, so pick the middle of the room and keep the antennas clear. eero notes that its units radiate mostly along their own plane, which is why a shelf beats the floor even when the room is central.
What blocks the signal most
Concrete is the barrier to plan around, because it takes the most signal and costs the most to cross. One concrete wall can cut 2.4 GHz by 10 to 20 dB and 5 GHz by 20 dB or more, in TP-Link blog figures that depend on the wall's thickness and density.
Every solid thing sits somewhere on a ladder from drywall to steel. NETGEAR ranks the tiers; eero calls plaster, lath and chicken wire particularly hard, and wood doors easier than a dense wall.
| Barrier | Printed loss | Source and limit |
|---|---|---|
| One concrete wall | 2.4 GHz: 10 to 20 dB; 5 GHz: 20 dB or more | TP-Link blog 2460, checked 18 November 2026; depends on thickness and density |
| Drywall, soft insulation | Minimal | NETGEAR large-homes hub, checked 18 November 2026; ranked tier, no dB |
| Wood, wood door | Light; easier than a dense wall | NETGEAR tier; eero, checked 18 November 2026 |
| Standard glass, tile, hollow brick | Moderate | NETGEAR tier; no dB; checked 18 November 2026 |
| Stucco wire mesh, solid brick, cinder block | Significant | NETGEAR tier; no dB; checked 18 November 2026 |
| Concrete, steel, mirrored or low-E glass | High | NETGEAR tier; no dB; checked 18 November 2026 |
| Plaster, lath, chicken wire | Particularly hard | eero support, checked 18 November 2026 |
Linksys says metal "can absorb or reflect" Wi-Fi, and that a signal does not pass well through water. That is why a mirror, a metal cabinet, a fish tank and a refrigerator all belong out of the straight line between the router and the rooms you care about.
| Maker | Between nodes | Extender to router | Limit and check date |
|---|---|---|---|
| eero | 20 to 30 ft; never more than 50 ft | Not printed; eero sells nodes, not extenders | Target band, 50 ft hard ceiling; checked 18 November 2026 |
| TP-Link | No more than 50 ft wireless | 25 to 40 ft external antennas; 20 to 35 ft internal | Longer runs need few obstacles and a strong router signal; checked 18 November 2026 |
| Linksys | Within two rooms or one floor | Not printed | Room count, not a distance; checked 18 November 2026 |
| Google Nest Wifi | 2 to 3 rooms; 1 to 2 in congested flats | Not printed | 7182840 gives 2 to 3 rooms; 7183150 caps at 2; checked 18 November 2026 |
| ASUS | Between router and the dead zone | Halfway | Qualitative; move closer if the node's own reception is poor; checked 18 November 2026 |
| NETGEAR | Not too far, not too close | Midway | Qualitative; no numeric band printed; checked 18 November 2026 |
Three rules follow from the tables. A node placed in the dead zone repeats a signal that is already weak, so put it between the router and the weak room. Units packed together interfere with each other, so respect the lower bound as well as the upper one. Where an Ethernet cable reaches the node, the wireless spacing rules relax.
Change the channel, not the power
Teal covers every radio setting: the SSID, the band and the channel. The channel is the setting that decides whether channels overlap, and it sits on the wireless page behind the admin panel that a router's local address opens. TP-Link prints tplinkwifi.net or 192.168.0.1 as that address, and either opens the panel.
The 2.4 GHz band carries 13 channels in the FCC staff presentation, and only three do not overlap: 1, 6 and 11. Channels 12 and 13 exist but generally need reduced power at the top band edge.
On 5 GHz, the high span from 5.725 to 5.850 GHz is the easy choice because it allows 1 W and needs no radar detection. The lower DFS ranges from 5.25 to 5.35 GHz and 5.47 to 5.725 GHz must detect radar.
- Open the wireless settings and scan for neighbouring networks, or use the router app's channel advisor.
- On 2.4 GHz, set 1, 6 or 11, picking whichever is least crowded at your address.
- On 5 GHz, set a channel in the 5.725 to 5.850 GHz span.
- Save and reconnect.
The power follows printed ceilings rather than a slider. The 2.4 GHz limit is 1 W peak conducted for digital modulation, and the 5.15 to 5.25 GHz span allows 1 W at an access point but only 250 mW at a client, both with antennas up to 6 dBi. Move the box before you move those numbers.
Split the bands
Teal also covers the band name, and the name is the lever. The 2.4 GHz band runs from 2400 to 2483.5 MHz; it reaches farther and bends around more obstructions, and its 802.11g headline rate is 54 Mbit/s.
The 5 GHz spans from 5.15 to 5.25, 5.25 to 5.35, 5.47 to 5.725 and 5.725 to 5.850 GHz carry more: 802.11ac peaks at 3.5 Gbit/s with MIMO, where 2.4 GHz cannot follow. TP-Link says to change one of the Wi-Fi names so the device sees two separate networks; with two names, a phone beside the router can be put on the 5 GHz one. Plugs work on 2.4 GHz only, TP-Link says, and it says most of its cameras do too, so they belong there where range matters.
The trade-off has its own page: 2.4 GHz versus 5 GHz covers which device belongs where.
Firmware, then Wi-Fi 6 or 7
Red marks the step that can brick the box: firmware. Update before spending on new hardware, and keep the router on mains power with a cable in the LAN port while it writes.
Routes differ by maker. NETGEAR uses the Nighthawk app, or Advanced > Administration then Firmware Update, TP-Link uses Advanced > System > Firmware Upgrade, ASUS uses Administration > Firmware Upgrade, Linksys uses Connectivity > Firmware Update and D-Link requires a wired connection, and menu names differ between firmware generations. Verizon delivers firmware over the air and prints no user procedure at all. The firmware update walkthrough has the full sequence.
A replacement router earns its price when the old one fails, stops getting security updates or cannot carry the device count, Waveform says; with one dead corner on an existing Wi-Fi 6 router it calls an upgrade to Wi-Fi 7 an expensive way to fix a cheap problem. Wi-Fi 6 is 802.11ax, standardised in 2021, with a 9.6 Gbit/s peak shared among devices. Wi-Fi 7 is 802.11be, standardised in 2024, with a minimum 30 Gbit/s at the MAC service point, not a promise for any one device. The 6 GHz band from 5925 to 7125 MHz is the less crowded one, added with Wi-Fi 6E, but allows indoor access points only 30 dBm EIRP.
Add wired backhaul
Amber is a cable in a port, and the back panel has two kinds. The WAN or Internet socket takes the modem feed; the LAN sockets are the ones for a second access point, so the cable goes from a LAN port on the main router to the uplink port of the second unit.
Twisted-pair Gigabit Ethernet allows a 100 m channel, equipment cords included.
With a cable in place, the wireless spacing rules relax: TP-Link says Deco spacing becomes more flexible with Ethernet backhaul, because wired units do not relay the signal and can sit farther apart.
Where no cable can run, powerline adapters carry the link over the mains circuit. TP-Link says speed depends on the age and quality of the wiring, electrical interference and whether both outlets share a circuit, and warns that surge protectors and power strips interfere. A coax run is the other wired shortcut: a MoCA adapter carries the traffic over the coaxial TV cable already in the walls, and Waveform rates it more consistent than powerline.
- On the second router, switch the operation mode to access point. TP-Link puts it under Advanced > Operation Mode, NETGEAR offers AP mode in its administration menu.
- Run the cable from a LAN port on the main router to the WAN port on the second unit, then power the second unit on.
- Give the access point the same SSID and password, and set its channel away from the main router's.
- If the second unit has no access point mode, TP-Link's fallback is to disable its DHCP server and join the two units LAN port to LAN port.
A wired node is also how to make a mesh network behave: Waveform's ranking is that a shared radio loses the most speed, a dedicated band less, and a cable almost nothing.
Extenders as the last cheap step
An extender is a small box that listens to the router and repeats the same signal. It costs less than a mesh node and buys one room, but a single-radio repeater shares the channel with the router, and Waveform says the throughput can then fall substantially, sometimes toward half.
Placement decides whether it helps at all. NETGEAR says midway between the router and the dead zone. TP-Link prints 25 to 40 ft from the router with external antennas and 20 to 35 ft with internal ones, and says the longer figure needs few obstacles and a strong router signal.
Set it around four feet high at the router's height, and keep it off a mirror, a metal shelf and the far side of a thick wall. The full pairing and login sequence is in setting up a Wi-Fi extender.
An extender earns its place for one dead zone at the far end of a home where no cable reaches. It does not fix a weak signal across the whole house, and Waveform says each chained extender adds another wireless hop and compounds the loss. Booster, repeater and extender mostly describe the same device, and makers use the three words inconsistently.
When a mesh system wins
A mesh system is several nodes on one network name, with the handoff handled for the phone. It wins when more than one room is weak, when the nodes can sit inside the maker's spacing, and when at least one of them can take a cable.
The printed spacing is wide enough to matter. eero asks for 20 to 30 ft and never more than 50 ft, TP-Link allows 50 ft wireless, Linksys counts two rooms or one floor, and Google counts 2 to 3 rooms or 1 to 2 in congested flats. Google's own pages disagree on that count: a second one prints no more than 2 rooms. A cable relaxes the distance figures; the room counts for Linksys and Google are printed without a wired version.
Mesh costs more than an extender, so the count of dead zones decides. Waveform puts one dead room with the extender and a whole house with mesh, and TP-Link calls mesh the better long-term solution. Mesh against an extender sets out the trade in full.
Test the change before and after
A change that feels faster where you stand can be slower two rooms away, which is why Waveform says to test from inside the dead zone rather than beside the box. Measure instead, in an order you can repeat.
- Walk the home first and write down the worst spots, with the room names.
- Stand still in each spot, hold the same device, note the signal bars and run a speed test.
- Change one thing only: placement, channel, band name, then hardware in that order.
- Repeat the same spots in the same order on the same device.
- Keep the change if every spot holds or improves; undo it if any spot is worse.
- Write the final placement and channel inside the router's battery door or on a label under the shelf.
Do the free steps first. If the router is new and not yet on the line, the cabling and admin login walkthrough on the home page comes before any of this, and what a router does explains which socket the modem feed belongs in.
Questions
Why is my WiFi signal so weak?
Usually because the router sits low, in a corner or against a wall, and the room is separated by concrete, metal or water. Distance and neighbour traffic add to it. Move the router to a central, raised spot first, then change the 2.4 GHz channel to 1, 6 or 11.
What blocks WiFi signals the most?
Dense mass: concrete, steel, brick, plaster and lath, and wire mesh in stucco. Metal reflects, water absorbs, and a microwave oven interferes while it runs. Wood, drywall and standard glass cost little.