Skip to main content

Port labels, addresses and setup pages from vendor documentation · checked Nov 2026 · Methodology

How to log in to your router

ResetWANLAN 1LAN 2LAN 3LAN 4PowerSSID ROUTER-4B21
Setup 192.168.0.1
Password printed below
Wi-Fi
The login page is a LAN-side page at the address the label prints.

By RouterPanel Editorial · Updated

Short answer

Connect your computer or phone to the router's own network, then open the address printed on the label and use the login printed beside it, or the password you set where the maker wants one. Change the admin password as soon as the page loads.

Connect your computer or phone to the router's own network, then open the address printed on the label and log in with the credentials beside it. Change the default admin password as soon as the page loads.

Read the label before anything

The label on the back or underside of the router carries the address you need and the default login that belongs to that box. TP-Link says the credentials vary by product and that the label is where to check them. TP-Link prints the details under headings such as Default Access, Default Settings or Default Wireless Access, and repeats them in the Quick Installation Guide inside the box. A Verizon Router CR1000A asks for the Network Settings password printed on the rear label.

Look for the words the maker chose rather than a fixed layout. TP-Link puts its label on the back or bottom of the device, and the same sticker can hold the Wi-Fi network name and the Wi-Fi password. Write the address down before the router goes under a desk.

The table below collects what each maker prints, as checked on 18 November 2026. Every address is model dependent and can be changed on a router already in use, so the label wins over the table.

Printed admin address and default login by maker, checked 18 November 2026
MakerPrinted admin addressDefault username and passwordFirst-login behaviour
NETGEARrouterlogin.net or http://192.168.1.1admin; the password set during setup, and admin / password after a factory resetThe setup password stays until a reset restores the printed pair.
TP-Linktplinkwifi.net or 192.168.0.1Older models admin / admin; newer models have none until you make oneNewer models force a custom admin password on first login.
Linksysmyrouter.local, linksysxxxxx.local, or https://192.168.1.1Password admin; if changed, a reset is neededThe local hostname is tried before the IP address.
D-Link DIR-605Lhttp://dlinkrouter.local or http://192.168.0.1Admin; the password field is blankA reset returns the password to blank.
StarlinkNo browser page; the Starlink appNone; the Wi-Fi password is set in the appDefault Wi-Fi name STARLINK until the app setup runs.
Xfinity WiFi Gatewayhttp://10.0.0.1, after Admin Tool is switched on in the Xfinity appUsername admin; a new password is created when access is enabledAccess is off until the account holder enables it in the app.
Verizon Router CR1000Ahttp://mynetworksettings.com or 192.168.1.1Network Settings password from the rear label; no usernameThe first visit opens an Easy Setup Wizard.
Verizon Internet Gatewaymynetworksettings.com; https://192.168.1.1 on WNC-CR200A and ARC-XCI55AX; https://192.168.0.1 on ASK-NCQ1338 and ASK-NCQ1338FAAdmin password from the label on the bottomThe certificate warning is passed through Advanced, then Proceed.

Connect to the router network

The login page answers only devices inside the router's own network, so join that network before you type any address, following the connection steps. On a phone or laptop, pick the Wi-Fi name printed on the same label and enter the Wi-Fi password from the label. A fresh box often ships with the Wi-Fi name and key already active and a printed card holding both.

The wired way is steadier. Plug an Ethernet cable into a LAN port and the other end into the laptop. Leave the WAN port for the modem cable, not the laptop.

Xfinity states the requirement plainly: the admin tool opens only while the device is on the home network, so join the home Wi-Fi before you try it.

Open the address in a browser

Put the address in the address bar, not in a search field, and press Enter. Type the http or https prefix exactly where the label prints one; the page uses a secure, self-signed certificate and browsers warn when they open it. On a Linksys or a Verizon Internet Gateway, https is part of the address.

A certificate warning on the first visit is normal for a local router. Open Advanced and choose Proceed; the page that follows is the login screen, not a broken site. If a hostname such as routerlogin.net or dlinkrouter.local does nothing, try the IP address printed beside it; entering the address directly is TP-Link's own fix.

The login screen asks for the credentials from the table, or for a new password where the maker requires one. Bookmark the page once it loads, so the next visit skips the hunt for the label. The full walk-through for the common address sits on the 192.168.1.1 router login page.

When the password is rejected

The NETGEAR login is case sensitive; the maker says so in its own login article, so retype the pair with Caps Lock off. A password that worked before and fails now is worth retyping before you reach for the reset button.

Check that you are typing the admin password and not the Wi-Fi password. The Wi-Fi key goes into the device's Wi-Fi settings; the admin pair goes into the browser page.

Two maker habits explain other rejections. Newer TP-Link models have no default admin password and expect you to create one on the first screen, so an old admin / admin pair fails on a new box. D-Link's DIR-605L page leaves the password field blank by default, so it stays empty until you set one.

After a factory reset the NETGEAR pair returns to admin / password, and a router that kept a setup password before the reset will reject that old one. If only the Wi-Fi key is wanted, see changing the Wi-Fi password, which is a separate setting.

When the page does not open

Work through the causes in order. The page stays blank often because the device sits on another network, so confirm the Wi-Fi name in the status bar matches the router's label before anything else. Turn off a VPN on the phone or laptop, since it can route the local address away from the router.

Next, swap the hostname for the IP in the table, and try the other prefix. A router that ignores http may answer https, and the certificate warning is passed the same way. A different browser rules out an extension blocking the local page.

Unplug the router, wait, plug it back in, and retry once it has restarted. If the address comes back blank on every device, look up the default gateway instead: ipconfig shows it on Windows, and the TCP/IP pane under System Settings, Network does the same on a Mac. The steps for each system are on the router IP address page.

192.168.1.1 is only one of several private address ranges. TP-Link and D-Link use 192.168.0.1, Xfinity uses 10.0.0.1 once the Admin Tool is unlocked, and a router already in use can be set to a different address, so try the other addresses before assuming a fault.

App-only routers

Starlink's router has no administrator portal at all: the app holds the router settings, the default Wi-Fi name is STARLINK, and the Wi-Fi password is set during app setup. No default admin pair exists to look for.

Xfinity keeps the page but locks it. The Admin Tool at 10.0.0.1 answers only after the account holder toggles Admin Tool access on in the Xfinity app, and that toggle is on newer gateways such as the XB6, XB7, XB8 and XB10. Older ones, the Wireless Gateway 1, Wireless Gateway 2 and XB3, do not support it. With Wi-Fi Intelligence on, the network name and password move entirely to the app.

The Verizon Router CR1000A takes a middle path: the login is a rear-label password entered on a page, and the first visit opens a setup wizard. Read the app's router menu before hunting for a page that the maker never built.

Reset as the last way back in

The reset button is the last route: recessed, marked Reset, and pressed with a straightened paperclip while the router runs. Hold times differ by maker (seven seconds on NETGEAR, ten on TP-Link and D-Link), so keep the button down through the blink pattern the manual describes rather than guessing.

A reset erases the Wi-Fi settings, the admin password and the port forwarding rules. Only the printed defaults come back, which is why the reset belongs after the cheaper checks. Save a backup of the settings first if the admin page still opens, so the rebuild is shorter.

What returns is the label pair: admin / password on NETGEAR, Admin with a blank field on D-Link. Join the router's network again with the printed Wi-Fi name, log in with the printed pair, and set a fresh admin password at once. The full procedure and hold guidance are on the router reset page.

Questions

How do I login to my Wi-Fi router?

Join the router's Wi-Fi network or plug into a LAN port, open the address on the label, and enter the printed admin pair. Change the admin password when the page loads.

How do I find the IP address of my router?

The label is first, because it prints the address the maker set. If the label is gone, read the gateway field from ipconfig on Windows or the TCP/IP pane on a Mac, or use the router IP address guide.

Why isn't the 192.168.1.1 login page opening?

The device is usually on another network, or the router uses a different address such as 192.168.0.1 or 10.0.0.1. Confirm the network, try the label address, and pass the https certificate warning before power-cycling.

Keep the router firmware current too; updating the router firmware covers that.

Sources

  1. kb.netgear.com: How do I log in to my NETGEAR router · checked Nov 19, 2026
  2. kb.netgear.com: How do I perform a factory reset on my NETGEAR router · checked Nov 19, 2026
  3. tp-link.com: 87 · checked Nov 19, 2026
  4. tp-link.com: 776 · checked Nov 19, 2026
  5. support.linksys.com: 81 en · checked Nov 19, 2026
  6. dlink.com: how do i upgrade the firmware on my router · checked Nov 19, 2026
  7. starlink.com: f9a1d602 9204 e70c a780 f2619d99f9c7 · checked Nov 19, 2026
  8. starlink.com: d68ed178 4d54 b486 b7d8 2a6273917632 · checked Nov 19, 2026
  9. learn.microsoft.com: ipconfig · checked Nov 19, 2026
  10. support.apple.com: mac · checked Nov 19, 2026
  11. xfinity.com: admin tool access · checked Nov 19, 2026
  12. verizon.com: knowledge base 239713 · checked Nov 19, 2026
  13. verizon.com: knowledge base 301456 · checked Nov 19, 2026

RouterPanel. "How to log in to your router." Updated Nov 19, 2026. https://howtosetuparouter.com/login-router/