Start with one device on one cable. The Ethernet lead goes into the WAN port, and the LED beside it picks the next step: orange means the jack is linked and the service is not arriving.
Start with one device, not all of them
A house where nothing loads hides two different faults. One failing laptop points at that laptop, its radio or its saved network. Every device failing at once points past the router, at the cable, the modem or the line. Split the two before you change a setting.
Take one laptop, switch its Wi-Fi off and put an Ethernet cable between it and a LAN port on the back panel. A wired link skips the radio completely, and the port LED lights when the pair is live. If that laptop loads a page, the WAN side is working and the fault is in the radio or in the other devices.
Teal is the radio side, and its own light answers for it. A 2.4 GHz or 5 GHz LED that is off means the band is disabled, so a phone that sees no network name has found a switched-off transmitter rather than a broken line. On a Verizon Router a solid green status LED means Wi-Fi is off outright.
When both the wired laptop and every phone fail, stop testing devices and follow the cable. The fault is upstream, and the next section is the one that matters.
Check the cable is in WAN
Amber is the cable and the jack it enters. Pull the Ethernet lead out of whichever hole it sits in and look at the labels before pushing it home again.
The upstream jack is printed WAN Port on a TP-Link Archer AX10 or AX1500, described as the port for a DSL or cable modem or an Ethernet jack. Netgear prints WAN and Internet on the same port, TP-Link prints Internet on other models, and Verizon prints Ethernet WAN on the CR1000A and CR1000B. All four name one jack, and it is the one that faces the line.
The LAN ports sit beside it and face your own rooms, not the modem. TP-Link keeps them separate from the Internet port, Asus names the LAN port distinctly, and Verizon fits three of them next to the single WAN port. A cable in LAN port 2 of a Verizon router is therefore a cable to a laptop, however firmly it is seated.
Cable modems label their side less helpfully. ARRIS prints no WAN label on its numbered Ethernet ports, and Motorola prints ETHERNET (LAN) on the port that is the upstream handoff. The cable still runs from the modem's Ethernet jack to the router's WAN or Internet jack.
Push the lead in until the tab clicks. TP-Link's first step is to check the cable is firmly seated in the WAN port; a worn lead is swapped for a new one.
Read the LEDs
The LED row is the panel talking, and the Internet or status light is the first thing to read. Its colours separate a cable fault from a service fault from a failing unit.
| Model | What you see | What it means | Do this |
|---|---|---|---|
| TP-Link Archer AX10 / AX1500 | Power LED flashing | starting, or a firmware upgrade | leave the power on |
| TP-Link Archer AX10 / AX1500 | Internet LED off | WAN port unplugged | cable from the modem to WAN Port |
| TP-Link Archer AX10 / AX1500 | Internet LED orange | port linked, no service | go to the modem and the line |
| TP-Link Archer AX10 / AX1500 | Internet LED green | service available | test the device, not the line |
| TP-Link Archer AX10 / AX1500 | 2.4 or 5 GHz LED off | band disabled | re-enable the radio |
| Netgear router | Internet LED solid amber | link, no Internet | check the modem and ISP |
| Verizon CR1000A / CR1000B | Status LED fast white blink | booting or restarting | wait |
| Verizon CR1000A / CR1000B | Status LED solid white | normal | nothing |
| Verizon CR1000A / CR1000B | Status LED solid green | Wi-Fi off | re-enable the radio |
| Verizon CR1000A / CR1000B | Status LED solid yellow | no internet | check the WAN cable |
| Verizon CR1000A / CR1000B | Status LED slow red blink | hardware or system failure | reset, then replace |
| Verizon CR1000A / CR1000B | Status LED fast red blink | overheating or update error | clear the vents and wait |
| Back panel, TP-Link / Verizon | WAN Port / Ethernet WAN label | the upstream jack | the modem cable goes here |
| Reset pinhole | No link after a known-good cable | settings may be wrong | hold 7 s (Netgear), more than 10 s (TP-Link), about 10 s (Linksys) |
An Internet LED that is off is the least ambiguous state in the table: the WAN port has nothing in it. An orange or amber light is the second: the jack is linked and the service behind it is missing, so the cable is not the question any more. Green means the router already has a line and the fault is on the device in your hand.
A port LED that stays dark means no powered-on device is on that port. Test the lead: plug the same cable from the WAN port into a LAN port; if both the Ethernet and Internet LEDs stay off, TP-Link says the port or the cable may be faulty, so try another cable first.
Check the address the router hands out
With the laptop wired to a LAN port, open the admin page at the address the router printed or the manual gives. Netgear uses routerlogin.net or 192.168.1.1, D-Link uses dlinkrouter.local or 192.168.0.1, and Verizon uses mynetworksettings.com or 192.168.1.1. Those are factory defaults, and the LAN address can be changed, so work from the default and not from memory.
A working handoff gives the laptop an address inside a private range. The three private blocks are 10.0.0.0/8, 172.16.0.0/12 and 192.168.0.0/16, reserved for the purpose since February 1996. An address of that shape and a page that opens mean the router's addressing is alive.
If the laptop carries an address from outside those blocks, or none, the handoff failed. Disconnect and rejoin the network, then check again. On the wire, pull the lead and reseat it at the LAN port; the port LED should light when the page loads.
The guide to finding the router's IP address covers the default gateway on each system, and the router login guide covers the page itself. When the address is right and the page still will not open, reconnect with a device connected to the router before assuming the unit is dead.
Power-cycle in the right order
Amber again, at both jacks. A power cycle is the whole cable-and-power sequence done once, cleanly, and the order of the two plugs is fixed.
- Pull the router's power lead, then the modem's.
- Wait with both off. Xfinity holds power out for at least fifteen seconds; a Starlink Gen 2 is replugged six times, two to three seconds apart, instead.
- Restore every cable: coax or fibre at the modem, Ethernet from the modem to the router's WAN port.
- Power the modem on and wait until its Online LED is steady.
- Power the router on and watch its power LED settle. A flashing Power light on a TP-Link or a fast white blink on a Verizon is a normal boot.
- Rejoin from the wired laptop and retest.
The printed sequence powers the modem first and the router second, and it waits in between: plug the modem in, wait for all the lights to stabilize, then power the router and wait for its lights to show the modem link. The wait is part of the procedure, not politeness. Coax runs to the wall outlet; the two power plugs are what the order fixes.
Keep the modem plugged in while its lights stabilize; pulling it out mid-wait is not a step in the printed sequence. If you need the full routine at length, the router reset guide has it, and the modem-to-router connection guide has the cable side.
Rule out the ISP
Before the router takes the blame, the modem's Online LED has to be solid. ARRIS prints a green Online light for a connected line, Motorola prints a solid ONLINE light for an online cable link, and an ONT shows solid lamps when normal. Blinking on the ARRIS is the modem scanning, not a connection.
A dark or still-blinking Online LED after a clean power cycle belongs to the line. Check the coax at the wall outlet, or the fibre connector at the ONT, and then call the provider with the state of that lamp. Before any router setting, the modem's internet light has to be on and both cables firmly seated.
To prove the router is not the fault, take the laptop to the modem and plug it into the modem's Ethernet port, bypassing the router. If the laptop gets online there, the line is fine and the router is at fault. If it does not, the fault sits at the modem or beyond it.
The cable at the wall is coax into the modem's Cable connector, or fibre into the ONT with Ethernet from the ONT onward. Both stop at the same rule: the router's WAN port is downstream of the modem, never upstream of the wall.
Factory reset as the last step
Red is the reset pinhole and the last tool in the box. Use it when the admin password is lost, when a setting you cannot find broke the WAN link, or when the unit answers but hands out no address. Skip it while the Internet LED is orange and the modem's Online light is dark: nothing in the router's settings caused that.
A reset erases the admin password, the network name and the Wi-Fi security on a Netgear, all configurations on a Linksys, and drops every connected device on an Xfinity gateway. Write those values down, then hold the pinhole only as long as the maker prints.
- Netgear: hold Restore Factory Settings or Reset on the back for seven seconds, then release.
- TP-Link: hold Reset or WPS/Reset for more than ten seconds, until the SYS LED shifts from slow flash to quick flash.
- Linksys: hold Reset for about ten seconds while the unit is powered on.
- Verizon: hold the rear Reset button fifteen seconds; Xfinity: hold it at least fifteen seconds unplugged and another thirty plugged back in.
Keep the power on unless the printed steps take it out first. Afterwards the unit reboots into its factory state and the login falls back to the factory default. Record the SSID, both passwords and the connection type before you start, as the reset guide sets out.
When the router itself has failed
Red again, and this time it stays. A slow red blink on a Verizon Router is a hardware or system failure; a fast red blink is overheating or a failed update. Neither clears with a cable change.
Escalate in the order already used, one step at a time: cable in WAN, LED, address, power cycle, ISP, reset. A unit that comes back with a solid white lamp after a reset has recovered; a steady green says the radio is still off. A unit that returns to the red blink has not.
No LED on any port after a known-good cable and a clean power cycle is the other verdict: TP-Link says the WAN port may be faulty at that point, and its printed next step is support. The setup guide covers the first connection on a replacement. If the router answers and only far-away devices drop, the fault is placement or radio, so work on the signal with improving the Wi-Fi signal instead of replacing hardware.
Questions
Why is my router connected but there is no internet?
Connected means the phone joined the Wi-Fi; it says nothing about the line. Read the Internet LED: green means the service is there and the device is the fault, orange or amber means the port is linked but the service is missing, and off means the WAN port is empty. Then go to the modem.
Does a factory reset fix a router that will not connect?
Only when a bad setting is the cause. It clears a lost admin password and a broken configuration, but it cannot restore a cable in the wrong port or a line the modem has not received. Try the cable, the LEDs and the modem first.