Skip to main content

Port labels, addresses and setup pages from vendor documentation · checked Nov 2026 · Methodology

How to change your home Wi-Fi password

ResetWANLAN 1LAN 2LAN 3LAN 4PowerSSID ROUTER-4B21
Setup 192.168.0.1
Password printed below
Wi-Fi
The field sits behind the admin login, on the wireless security screen.

By RouterPanel Editorial · Updated

Short answer

Open the router's admin page, reach the wireless security screen, choose WPA2 or WPA3, and save a new passphrase. Every device drops at the save, so reconnect the ones you keep.

Open the router's admin page, find the wireless security screen, choose WPA2-Personal or WPA3-Personal, and save a new passphrase you have not used elsewhere. Every device drops at the save, so have the new key ready and reconnect the ones you keep, one by one.

Before you start

The LAN port is the cable path. Plug an Ethernet cable into a LAN port and leave the WAN, or Internet, port alone, because that one is meant for the modem. A wired computer plugs into a LAN port rather than joining over Wi-Fi; TP-Link still says to reconnect each device after the change.

The label on the bottom carries the default admin login, usually admin/admin or a unique code printed on the device. If the label has gone, the steps to sign in are on the router login page, and an address that refuses to open is covered under finding the router's IP address.

Write the old passphrase down before you save, so you still have it while you move devices across; the new one replaces it on the router.

The steps

  1. Connect the computer to a LAN port with an Ethernet cable, or join the network on a phone.
  2. Type the router's local address in the browser and sign in.
  3. Open the wireless menu and choose the security entry for the main SSID, not the guest one.
  4. Pick WPA2-Personal or WPA3-Personal in the security mode dropdown.
  5. Type the new passphrase in the Password, Passphrase or Pre-Shared Key field and press Apply or Save.
  6. Let the router confirm the write before you touch the second band.

The reset pinhole is the small recessed hole, and it stays untouched through all six steps; it wipes settings rather than saving them.

Which encryption mode

The security mode sits on the same wireless screen as the SSID, in a dropdown. That dropdown is not just two entries: Netgear says a router can come with preset WEP, WPA, WPA2 or WPA3 security, TP-Link lists the same four protocols, and most newer TP-Link routers support a WPA2/WPA3 transition mode.

What WPA2 and WPA3 certification each require, from the Wi-Fi Alliance, checked on 18 November 2026
ModeWhat certification requiresStated inChecked
WPA2-PersonalMandatory for every Wi-Fi CERTIFIED device; every Wi-Fi device has shipped with WPA2 since 2006The WPA3 announcement of 25 June 2018, which keeps WPA2 mandatory18 November 2026
WPA3-PersonalMandatory for Wi-Fi CERTIFIED devices; Protected Management Frames required; outdated legacy protocols disallowedThe Alliance security overview18 November 2026

Pick WPA3-Personal wherever the list offers it: WPA3 certification requires Protected Management Frames and disallows the outdated legacy protocols.

An older router that lists only WPA2-Personal is still on solid ground. WPA2 has been mandatory for certified devices since the Alliance release of 25 June 2018 and has shipped on every Wi-Fi device since 2006, so it is the floor rather than a weak choice.

Do not leave the mode on WEP while WPA2 sits in the same list: Netgear says WEP is easily decoded, and TP-Link says to avoid it. A gadget that joins only on WEP can go on the guest network instead, which TP-Link suggests for smart-home devices.

After you save

Every device holding the old key is disconnected after the save, TP-Link says, and each one has to be rejoined with the new key. Work in an order that keeps a working screen in your hand:

  • Phone or laptop: forget the old entry, choose the SSID again and type the new key when asked.
  • Television, streaming stick or console: open its network settings and enter the key with the remote or controller.
  • Plug, camera or doorbell: run its pairing step once more from the maker's app.

The wired computer stays on the LAN port, and TP-Link's instruction to reconnect each device covers it too. Devices you leave switched off stay off until you turn them on and rejoin them. The longer walkthrough, band by band, is under changing the Wi-Fi password.

Questions

Can I change the Wi-Fi password from my phone?

Yes. Join the network, open the local address in the phone browser and sign in, then use the same security screen. The phone drops at the save, so rejoin with the new key afterwards.

What happens to devices already connected?

They lose access at the save and stay off until each one gets the new key. Phones and laptops rejoin from their Wi-Fi settings; plugs, cameras and doorbells may need the pairing step run again.

Sources

  1. wi-fi.org: security · checked Nov 19, 2026
  2. wi-fi.org: wi fi alliance introduces wi fi certified wpa3 security · checked Nov 19, 2026
  3. wi-fi.org: Wi Fi_CERTIFIED_WPA3_Technology_Overview_202101 · checked Nov 19, 2026
  4. kb.netgear.com: How do I change the WiFi security protocol that my NETGEAR router uses · checked Nov 19, 2026
  5. tp-link.com: 2315 · checked Nov 19, 2026

RouterPanel. "How to change your home Wi-Fi password." Updated Nov 19, 2026. https://howtosetuparouter.com/change-wifi-password/how-to-change-home-wifi-password/