Type 192.168.1.1 into the address bar of a device already joined to the router's network, then log in with the label's admin pair where one is printed, or create an admin password if the router asks. That address is one private number, so check first that it is the gateway your own device uses.
Why that address
192.168.1.1 sits inside one of the three blocks that RFC 1918 set aside for private internets in February 1996. IANA labels all three Private-Use, and none is globally reachable, which is what lets a router own the address without asking the ISP for it.
The address is a default, not a promise. RFC 1918 reserves the blocks and fixes no single address inside them, so a router can be moved off 192.168.1.1 during setup. The table shows which range could hold it.
| Private range | Is 192.168.1.1 inside? | The check that rules it out |
|---|---|---|
| 10.0.0.0 to 10.255.255.255 (10/8) | No | The first octet would have to be 10, and here it is 192. |
| 172.16.0.0 to 172.31.255.255 (172.16/12) | No | The first octet would have to be 172, with a second octet from 16 to 31. |
| 192.168.0.0 to 192.168.255.255 (192.168/16) | Yes | Both leading octets are 192.168 and any third octet fits, so 192.168.1.1 is inside. |
A gateway of 10.x or 172.16 to 172.31.x means the network does not use this address. Read the gateway and type it instead; the routine is in finding your router's IP address.
Open it in the right order
An Ethernet cable goes into a LAN port, never the WAN port. The WAN port faces the modem and the LAN ports face your devices; one cable into any of them puts the laptop on the router's own side. A phone joins by Wi-Fi with the SSID and key from the label.
Type the number into the address bar at the top of the browser, not into the search box, and press Enter.
If the browser turns the number into a web search, put http:// in front and send it again. The page is served by the router itself, so it opens even with the internet down.
The first screen may ask for a password or, on a recent TP-Link, ask you to create one; what each maker expects is in how to log in to your router. Cabling is in connecting to a router.
The credentials
On some routers the label holds the admin login: Verizon prints a user name of admin with a unique password. Current TP-Link models print the Wi-Fi key on the label instead and ask you to create an admin password at first login. A NETGEAR router uses the user name admin with the password set during setup. Read the label before trying admin and admin.
Enter them and press the button beneath. Passwords are case-sensitive; copy the label exactly.
Change the admin password on the first visit. A router left on its factory default accepts the label value from anyone who reaches it.
When the page will not open
When the page will not open, the fault is an address or a login the router rejects, or a device off its network. Work down the list before the reset pinhole, which is red-zone work.
- Check the device. A phone on mobile data cannot reach the address, and a guest SSID may not either; guest networks can be kept off the main one.
- Read the gateway from the connected device and type that instead. The router may have been moved off 192.168.1.1.
- Put http:// in front, or try a second browser.
- Power-cycle: pull the router's power, wait, and plug it back in. Give it time to boot before you retry.
- Press the reset pinhole with a paper clip and hold — about 6 to 15 seconds, depending on the maker — until the LEDs blink, then release. The full procedure is in how to reset a router.
A reset returns the address to the factory default and the admin password to the factory value — on many routers that is the pair on the label, where one is printed; on a NETGEAR the user name is admin and the password is password. Everything set since the router left the factory goes with it.
Questions
Is 192.168.1.1 the same on every router?
No. It is a common default inside the 192.168/16 block, but a router can be set to another private address, such as 192.168.0.1. The gateway on the device is the address that works.
Why does 192.168.1.1 time out?
The device is usually on a different network, or the router uses another address. Rejoin the SSID or reseat the LAN cable, read the gateway, and open that.