No, not on an ordinary router. Pulling the plug is a restart: the Wi-Fi name, the Wi-Fi password and the admin password all survive the next boot. Only the reset pinhole, held for the time the maker prints, wipes them. The exception is Starlink Gen 2, which has no reset button and resets after six power cycles.
What unplugging does
A power cycle means pulling the power lead at the router. It is the first move for a stalled page, a device that will not join or Wi-Fi that dies in one room.
- Pull the power plug from the router.
- Wait 30 seconds.
- Plug it back in and let the lights settle.
- Rejoin with the saved password.
| Action | What you do | Hold |
|---|---|---|
| Power cycle, ordinary routers | Pull the plug at the router, wait 30 seconds, plug back in | none |
| NETGEAR | Power light on; hold Reset on the back with a paper clip | 7 seconds |
| TP-Link | Powered on, hold Reset until the SYS LED quick-flashes | More than 10 seconds |
| Linksys Smart Wi-Fi | Admin page Diagnostics, Reset; or hold Reset and release | About 10 seconds |
| ASUS (RT-AC66U B1 page) | Admin page Administration, Restore; or hold RESET until the LED flashes | 5 to 10 seconds |
| D-Link DIR series | Paper clip in the recessed reset hole, then release | About 10 seconds, 7 on the DIR-878 |
| Google Nest Wifi | Home app: Factory reset network; bottom button as fallback | 10 seconds on the button (Nest Wifi router; 12 on Pro) |
| eero | Hold Reset until the LED flashes red | About 15 seconds |
| Xfinity WiFi Gateway | Unplug, hold Reset at least 15 s, release, plug in, hold 30 s | At least 15 seconds, then 30 |
| Verizon Router | Powered on, hold the rear Reset, then wait | 15 seconds |
| Starlink Gen 2 | Unplug and replug six times, 2 to 3 seconds apart | Six cycles |
What a factory reset does
Red is the pinhole, recessed: a paper clip hole on D-Link, a button on the back elsewhere. On eero the button sits on the back on the first generation, the Pro, PoE 6, PoE 7, PoE Gateway, Max 7 and Pro 7, on the side on a Beacon, and on the bottom on the eero, 6, 6 extender, 6+, Pro 6, Pro 6E, 7 and Outdoor 7; Nest Wifi puts its button on the bottom. Held on a powered router, it wipes the SSID, both passwords and the internet settings, and falls back to the label's credentials. Every device drops and stays offline until set up again.
A reset reboots the router, but it does more than a reboot: the configuration goes, the firmware stays.
Hold times the makers print
Hold times are printed, not guessed: NETGEAR seven seconds, TP-Link more than ten, eero and Verizon fifteen; Xfinity wants at least fifteen unplugged and thirty more plugged in. The table above holds the rest.
Watch the light, not the clock: the SYS LED quick-flashes on TP-Link, the power LED flashes on ASUS and turns orange on D-Link, the eero LED flashes red.
Which one to use
Restart anything that recovers by itself: a page that will not load, one dead room, a console that dropped off. Reset when the admin password is lost, the router came from someone else or you are passing the box on. On a router that will not connect it is the last step.
Back up first. Take the save where the admin page offers it: Restore/Save/Upload Setting on ASUS, Backup and Restore on TP-Link. Write down the Wi-Fi name and password, the admin password and any port forwards. Afterwards set a new Wi-Fi password and work through a router that is not connecting; the full sequence is in how to reset a router.
Questions
Will I lose the Wi-Fi password if I unplug the router?
No. The password and the network name are stored and come back at boot; only the reset pinhole takes them. Starlink Gen 2 is the exception.
How long do I hold the reset button?
As long as the maker prints: seven seconds on NETGEAR, more than ten on TP-Link, fifteen on eero and Verizon. Release when the status light signals.