Skip to main content

Port labels, addresses and setup pages from vendor documentation · checked Nov 2026 · Methodology

Which way do you feed a router table?

ResetWANLAN 1LAN 2LAN 3LAN 4PowerSSID ROUTER-4B21
Setup 192.168.0.1
Password printed below
Wi-Fi
The feed side is the table edge the fence and the bit work against.

By RouterPanel Editorial · Updated

Short answer

Feed the stock from the right-hand side of the table to the left, across the front of the bit, so the cutter works against the push. The infeed fence face, the clamp face, keeps the edge true.

Feed the stock from the right-hand side of the table to the left, across the front of the bit, so the cutter works against the push. The infeed fence face, the clamp face, keeps the edge true.

The rule

Seen from above, the bit turns clockwise. The stock's edge rides the clamp face and meets the back of the bit, where the teeth travel right while the stock travels left; the teeth take a shaving instead of climbing. Kreg states the rule as feeding against the rotation, and says a stock fed with it can be ejected violently.

Three makers print the direction for a fence cut: right to left. Bosch adds across the front of the bit and puts the rule in capitals; Amana says push right to left; Woodcraft states the same rule as pushing against the rotation.

The direction changes when the work moves to the far side of the bit, or when a pass is fed with the rotation on purpose. The table gives each cut type and the rule behind it.

Cut type, the direction the stock takes, and the rule that sets it, with the fence set for an edge cut; checked 18 November 2026
Cut typeDirection the stock takesRule that sets it
Edge cut, stock on the fenceRight to left, across the front of the bitFeed against the rotation
Groove run along the fenceRight to left, unchangedThe fence still holds the stock on the near side
Inside cut, work around the bitLeft to rightThe work has moved to the far side of the bit
Climb cut, small passLeft to right, with the rotationThe bit is allowed to pull the stock

Two rows run right to left, one reverses for an inside cut, and the climb row is the exception.

Right to left across the front

Set the fence faces close to the bit so the edge has the shortest gap to bridge, and turn the bit by hand to check clearance. A featherboard on the infeed side, ahead of the bit, has its first short feather just grazing the work; the longer feathers press as the stock feeds on.

Bring the right-hand end to the bit and push it leftwards across the front. The bit meets the leading corner, and the stock stays hard on the clamp face, past the outfeed fence face and clear of the opening. Push blocks carry the trailing end.

Inside cuts

An inside cut puts the work around the bit: an opening, a frame interior, or a pin-guided pattern with the bearing on the inside edge. The work sits on the far side, so the stock travels left to right, still against the rotation as seen from that side.

DeWalt gives the pair as counter-clockwise on an outside cut and clockwise on an inside cut; an inverted motor flips both readings to the stock's point of view.

A groove along the fence is not that kind of cut. The fence holds the stock on the near side, so the direction stays right to left. What changes is depth per pass: a Makita trimmer limits a groove to 3 mm a pass. DeWalt caps bit diameter at 2-1/2 in (63 mm). The plate, ring and fence sit in how to set up a router table.

When a climb cut is wanted

A climb cut feeds with the rotation. The teeth travel the same way as the stock, so the bit takes hold and pulls the work through instead of pressing it back. That is why DeWalt advises smaller cuts and minimal material per pass: with the bit pulling, control is lost.

The Woodcraft guide says feeding with the rotation loses control and scallops the edge. Kreg names the worst case, with the stock ejected and the hand able to contact the bit.

Keep the stock hard on the clamp face and the push blocks set.

Questions

What happens if you feed the wrong way?

The bit takes the stock and runs with it. Control passes from the hands to the bit; the edge can scallop and the stock can be ejected.

Does feed direction change for a groove?

No, if the groove runs along the fence. The stock stays on the near side and the fence holds it, so it goes right to left like an edge cut. Apart from a deliberate climb pass, only an inside cut, with the work around the bit, reverses the feed.

Sources

  1. Kreg PRS2100 benchtop router table manual · checked Nov 19, 2026
  2. Bosch 1617/1618 router manual · checked Nov 19, 2026
  3. DeWalt DW616/DW618 router manual · checked Nov 19, 2026
  4. Amana Tool router bit technical information · checked Nov 19, 2026
  5. Woodcraft Router Table Basics guide · checked Nov 19, 2026
  6. Rockler Adjustable Table Featherboard · checked Nov 19, 2026
  7. Makita RT0700C trimmer manual · checked Nov 19, 2026

RouterPanel. "Which way do you feed a router table?." Updated Nov 19, 2026. https://howtosetuparouter.com/router-table/router-table-feed-direction/